#Atomizer rosin flux powder professional#
#Atomizer rosin flux powder free#

If you work with solder regularly, I suggest a strong one. If you are working with solder, and it is sporadic, I suggest you have a small one. I have now ordered one fume extractor for up close and will be looking into another. I don't know if this is part of the exposure or just age. Now I have to wait for my sinus membrane to recover before I can get back to my project (which takes more solder than the average computer board). I did this for 3 consecutive days until I realized that it was more damaging than I thought. Thinking this is just pollen I returned the following day to my beloved project and soldered for 4 hours. I also found that my eyes were gunked up. I quickly found after 3 hours of soldering that I had a head ache and the next morning my sinuses were bothering me. When I first started working with solder at home I thought that I was just going to be working a few times here and there (Stained Glass Hobby).

#Atomizer rosin flux powder professional#

I worked on electronic boards years ago and did not find I had a problem but I also worked in a professional environment that filtered the room. If you don't have an extractor then stick to about 10 minutes of soldering a day and then get plenty of fresh air inside you afterwards and you should be okay. Position the extractor hose directly above the area you are soldering and make sure it is working properly before going anywhere near the area being soldered. In soldering metals, flux serves a threefold purpose: it removes any oxidized metal from the surfaces to be soldered, seals out air thus preventing further oxidation, and by facilitating amalgamation, improves wetting characteristics of the liquid solder. If you are doing a lot of soldering make sure you take a lot of breaks and get some fresh air inside you as well as having a decent extractor that sucks well. Like cigarettes, the fumes can also be invisible to the naked eye, but are more damaging. I had no idea how damaging those fumes could be. I had no previous lung problems before that job, I was physically fit, 6' 5' tall, 17 stones and I was 38 years old at that time. This thread is old but I thought i'd post it in case anybody new reads it.ĭownload the safety data sheet from the internet for the solder wire you are using and read the hazards before using it. I was employed in that position for 18 months only and am now registered disabled with lung damage after being challenge tested at the Royal Brompton Hospital in London. I have occupational asthma from solder fumes containing Rosin (colophony) after my job as an RF Development technician. Trust me, it's not worth the risk and I'm talking from experience. Invest in a good extractor, not a cheap one.

#Atomizer rosin flux powder free#

Other solder wires that are Rosin free cause other health problems and are rubbish to solder with. This causes asthma if you are over exposed and is irreversible. The best solder wire contains something called Rosin that helps the solder flow when hot. Most residues are the result of inadequate or partial cleaning, and can be eliminated by simply repeating the cleaning step.All solder fumes can cause occupational asthma and other health problems (leaded and lead-free) if used for long periods at a time. That means they fully evaporate without leaving anything behind. Usually residues form on circuit boards due to problems inherent in the nature of the soldering and cleaning process.Ĭhemtronics printed circuit board (PCB) cleaners, like Flux-Off flux removers and Electro-Wash maintenance cleaners, are filtered and made of 100% volatile solvents. 1-48 of 744 results for 'rosin soldering flux' Results Amazon's Choice SRA Solder 135 Rosin Paste Soldering Flux For Electronics, No Clean Flux Made for Lead and Lead-Free Solder Circuit Boards and Copper Electrical Wire - Safe Clean Residues with No Goopy Mess (2oz Jar) 14,637 4K+ bought in past month 799 List: 10. When contamination is found on the board after the cleaning step, the customer often assumes it has come from the cleaner itself. The appearance of white residues on circuit boards is a recurring problem in PCB assembly, and generates many questions and complaints for the Tech Support hotline.

FOCCUS Transportable I & M Fiber Optic Cleaning Kit.

Chemask WF – Water Filterable Solder Mask.

Chemask NA – Non-Ammoniated Solder Mask.

Chemask HV - High Viscosity Peelable Solder Mask.

CircuitWorks Epoxy Overcoat (Adhesive Syringe).

CircuitWorks Conformal Coating Remover Pen.Static Free Mat and Benchtop Reconditioner.Coventry 12820 Precision Cleaning Solvent.Konform SR-X Silicone Conformal Coating.